Service Details
- Home
- Service Details
Most Chinaware like disks, plates, bowls, cups, mugs, vases etc. are made in Chaozhou Guangdong China. The onsite quality inspections of Chinaware will normally be inspected as follows:
INSPECTION CHECKPOINTS | RESULTS | COMMENTS |
---|---|---|
A. Quantity & assortment check | OK | |
B. Shipping marks & packing | OK | |
C. Labels, logos and colors | OK | |
D. Styles & measurements | OK | |
E. Onsite safety and function tests | OK | |
F. Special requirements | OK | |
G. AQL workmanship (Visual defects) |
OK |
For professional third party inspection services, the technical classifications are as below:
The Chinaware inspection checkpoints:
ONSITE INSPECTION CHECK LIST | COMMENTS | RESULT |
---|---|---|
Check capacity (volume) by weighing the item or by using a capacity gauge ( the mug, bowl and the container claimed with the volumn)-The results must conform with the specifications.-S2 | PASSED | |
Test the item for water leakage during the entire inspection period.-Fill the item with water then place onto a paper to check there is no leakage at all.-S2 | N/A | |
Hand washing test -- --Wash the product with cotton fabric in cold water of room temperature (about 20--35degree) and hot water of tempertature (about 80 -- 90 degree) -- During washing, dip product into the water and wiping the whole surface of the product -No color should be removed from the item’s surface during the test and no printing, markings or paint should fade.-3 pcs | FAILED | |
Test the fit of the lid. and lid can not falls off when the teapot is tilted toward 90 degrees-If the item has a lid - The lid should fit well.-S3 | PASSED | |
Check if items stand properly when pieces are stacked up, if this test fail, please state the cause clearly on inspection report and take photos- 1)Stack the products (60 pieces for the plate/reference and 12 pieces for bowl/reference and cup/reference ); 2) Ensure they can stack properly and do not wobble or tilt over-S2 |
PASSED | |
Perform a fitting test check-The lid should fit the base well.-II | PASSED | |
Perform a fatigue test-On all adjustable parts. Do this 20 times.-S2 | PASSED | |
Test the strength of the handle.--S2 | PASSED | |
If the product is designed for use in a dishwasher and/or microwave oven, place it in a dishwasher and run the dishwasher for one cycle during the inspection period and also 10 minutes in the micro-wave oven.-If the product is designed for use in a dishwasher and/or microwave oven, place it in a dishwasher and run the dishwasher for one cycle during the inspection period and also 10 minutes in the micro-wave oven.-S2 |
PASSED | |
Compare the inspection sample with the approval sample.-II | PASSED | |
Perform a wobble test on a flat glass panel. Check both the top rim of the glass and the bottom.-There should be no wobbling of the base or the rim.-I | PASSED |
Chinaware 3rd party shipment inspection in China, Chinaware third party shipment inspection, Chinaware third party shipment inspection services, Chinaware shipment inspection in China, Chinaware shipment inspection, Chinaware third party shipment inspection services, Chinaware shipment inspection services in China, Chinaware shipment inspection services, Chinaware 3rd party shipment inspection, Chinaware 3rd party shipment inspection, Chinaware 3rd party shipment inspection services in China, Chinaware shipment inspection services, Chinaware third party shipment inspection services in China, Chinaware third party shipment inspection in China, Chinaware 3rd party shipment inspection services, Chinaware 3rd party shipment inspection services, Chinaware third party shipment inspection
3rd party pre products goods factory onsite inline final Random AQL PSI TPI FRI DUPRO third party on-site in-line pre- QA QC check quality control assurance services in China India Vietnam Thailand Malaysia Bangladesh Taiwan.