Service Details
- Home
- Service Details
Most Chinaware like disks, plates, bowls, cups, mugs, vases etc. are made in Chaozhou Guangdong China. The onsite quality inspections of Chinaware will normally be inspected as follows:
INSPECTION CHECKPOINTS | RESULTS | COMMENTS |
---|---|---|
On-site safety, regulation & function tests | OK | |
Labels, markings, logos & barcodes checks | OK | |
Measurements & sizes checks | OK | |
Product specs, and special requirements verifying | NOT OK | |
Packaging, safety and drop tests onsite | OK | |
Aesthetic, visual defects, workmanship, surface and function inspections | N/A | |
Quantity & assortment inspections | OK |
For professional third party inspection services, the technical classifications are as below:
The Chinaware inspection checkpoints:
ONSITE INSPECTION CHECK LIST | COMMENTS | RESULT |
---|---|---|
Perform a wobble test on a flat glass panel. Check both the top rim of the glass and the bottom.-There should be no wobbling of the base or the rim.-I | FAILED | |
Test the strength of the handle.--S2 | PASSED | |
Test the item for water leakage during the entire inspection period.-Fill the item with water then place onto a paper to check there is no leakage at all.-S2 | FAILED | |
Hand washing test -- --Wash the product with cotton fabric in cold water of room temperature (about 20--35degree) and hot water of tempertature (about 80 -- 90 degree) -- During washing, dip product into the water and wiping the whole surface of the product -No color should be removed from the item’s surface during the test and no printing, markings or paint should fade.-3 pcs | FAILED | |
Compare the inspection sample with the approval sample.-II | PASSED | |
If the product is designed for use in a dishwasher and/or microwave oven, place it in a dishwasher and run the dishwasher for one cycle during the inspection period and also 10 minutes in the micro-wave oven.-If the product is designed for use in a dishwasher and/or microwave oven, place it in a dishwasher and run the dishwasher for one cycle during the inspection period and also 10 minutes in the micro-wave oven.-S2 |
PASSED | |
Perform a fatigue test-On all adjustable parts. Do this 20 times.-S2 | PASSED | |
Check capacity (volume) by weighing the item or by using a capacity gauge ( the mug, bowl and the container claimed with the volumn)-The results must conform with the specifications.-S2 | PASSED | |
Check if items stand properly when pieces are stacked up, if this test fail, please state the cause clearly on inspection report and take photos- 1)Stack the products (60 pieces for the plate/reference and 12 pieces for bowl/reference and cup/reference ); 2) Ensure they can stack properly and do not wobble or tilt over-S2 |
PASSED | |
Test the fit of the lid. and lid can not falls off when the teapot is tilted toward 90 degrees-If the item has a lid - The lid should fit well.-S3 | FAILED | |
Perform a fitting test check-The lid should fit the base well.-II | PASSED |
Chinaware third party inspection, Chinaware third party inspection in China, Chinaware 3rd party inspection, Chinaware 3rd party inspection services in China, Chinaware third party inspection, Chinaware third party inspection in China, Chinaware third party inspection services in China, Chinaware 3rd party inspection, Chinaware 3rd party inspection services, Chinaware third party inspection services, Chinaware third party inspection services, Chinaware 3rd party inspection in China, Chinaware third party inspection, Chinaware third party inspection services, Chinaware third party inspection services in China, Chinaware 3rd party inspection services, Chinaware third party inspection services
3rd preshipment products goods factory onsite inline final Random AQL PSI TPI FRI DUPRO on-site in-line pre-shipment QA QC check quality control assurance services in China India Vietnam Thailand Malaysia Bangladesh Taiwan.