Service Details
- Home
- Service Details
The preshipment inspections of tableware are very important to make sure all safety requirements, PO stipulations, production specifications are met. The quality checks will mostly follow below methods:
INSPECTION CHECKPOINTS | RESULTS | COMMENTS |
---|---|---|
Quantity & assortment verifying | NOT OK | |
On-site safety, regulation & function tests | OK | |
Aesthetic, visual defects, workmanship, surface and function checks | N/A | |
Packaging, safety and drop tests onsite | OK | |
Product specs, and special requirements checks | NOT OK | |
Measurements & sizes checks | NOT OK | |
Labels, markings, logos & barcodes QC check | OK |
As the quality control inspections can happen at any stage of manufacturing, so there are:
The checklist for onsite quality inspection test will be like below:
ON-SITE INSPECTION CHECK LIST | COMMENTS | RESULT |
---|---|---|
Check if items stand properly when pieces are stacked up, if this test fail, please state the cause clearly on inspection report and take photos- 1)Stack the products (60 pieces for the plate/reference and 12 pieces for bowl/reference and cup/reference ); 2) Ensure they can stack properly and do not wobble or tilt over-S2 |
FAILED | |
Compare the inspection sample with the approval sample.-II | PASSED | |
Test the strength of the handle.--S2 | N/A | |
If the product is designed for use in a dishwasher and/or microwave oven, place it in a dishwasher and run the dishwasher for one cycle during the inspection period and also 10 minutes in the micro-wave oven.-If the product is designed for use in a dishwasher and/or microwave oven, place it in a dishwasher and run the dishwasher for one cycle during the inspection period and also 10 minutes in the micro-wave oven.-S2 |
PASSED | |
Perform a fitting test check-The lid should fit the base well.-II | PASSED | |
Perform a fatigue test-On all adjustable parts. Do this 20 times.-S2 | FAILED | |
Perform a wobble test on a flat glass panel. Check both the top rim of the glass and the bottom.-There should be no wobbling of the base or the rim.-I | FAILED | |
Check capacity (volume) by weighing the item or by using a capacity gauge ( the mug, bowl and the container claimed with the volumn)-The results must conform with the specifications.-S2 | FAILED | |
Hand washing test -- --Wash the product with cotton fabric in cold water of room temperature (about 20--35degree) and hot water of tempertature (about 80 -- 90 degree) -- During washing, dip product into the water and wiping the whole surface of the product -No color should be removed from the item’s surface during the test and no printing, markings or paint should fade.-3 pcs | N/A | |
Test the item for water leakage during the entire inspection period.-Fill the item with water then place onto a paper to check there is no leakage at all.-S2 | PASSED | |
Test the fit of the lid. and lid can not falls off when the teapot is tilted toward 90 degrees-If the item has a lid - The lid should fit well.-S3 | PASSED |
tableware 3rd party factory Check services in China, tableware factory Check in China, tableware third party factory Check services, China tableware factory Check, tableware third party factory Check, tableware 3rd party factory Check services, tableware 3rd party factory Check in China, tableware factory Check services in China, tableware third party factory Check in China, China tableware 3rd party factory Check services, tableware 3rd party factory Check, China tableware third party factory Check services, tableware factory Check services, China tableware third party factory Check, China tableware factory Check services, tableware third party factory Check services in China, China tableware 3rd party factory Check
3rd party preshipment products goods onsite inline final Random AQL PSI TPI FRI DUPRO third party on-site in-line pre-shipment QA QC quality control assurance inspection services in China India Vietnam Thailand Malaysia Bangladesh Taiwan.