Service Details
- Home
- Service Details
1. there are different inspection types for different production stages:
2. The on-site checking procedures for soft-line product inspections are as follows:
As an example, the quality inspection protocols would normally like this:
INSPECTION LIST | COMMENTS | RESULT |
---|---|---|
Barcode scanning Test-The sample size for each type of the barcode should be scanned as following: - Barcode label on products - Barcode label per carton: |
PASSED | |
Count and record the number of stitches per inch 每英寸针数 |
PASSED | |
Symmetric check- check if the sleeves, collar, shoulders , pocket design, etc. are symmetric- check if the garment twist and measure the difference if found 对称检查-检查袖子、领子、肩膀、口袋等设计是否对称-检查衣服的捻度,如果发现有差异就测量一下 |
PASSED | |
MAIN SEW-IN LABEL (SUPPLIED BY SUPPLIER) TO BE ATTACHED ON THE INSIDE NECK. | N/A | |
FABRIC STRETCH (SEAMLESS ITEMS) - CHECK THE FABRIC HAS CORRECT STRETCH (ITEMS MUST BE STRETCHY. WE HAD SOME ITEMS RECENTLY FROM THE SUPPLIER THAT DID NOT STRETCH ENOUGH TO WEAR COMFORTABLY). 面料弹力(无缝物品) -检查面料是否有正确的弹性(物品必须有弹性。我们最近从供应商那里买了一些穿起来不舒服的衣服)。 |
PASSED | |
*S*: Needle detecting test without metal button or decoration 针检测试(只对没金属配件的) |
PASSED | |
Fabric-weight check for knitting garment with cutting equipment (unit: grams per square meter). This must be Performed from three places on one sample or from the bulk fabric available. Mark whether the sample was ironed before the test-A result within +/-5% of the clients requirements is acceptable -3 pcs ( Pcs)--克重检验 | PASSED | |
Seaming strength test-Test the strength of the seams by hand. especially on sideseams ,armhole, pockets. strength test along seam to check stithes if broken. 接缝强度测试用手测试接缝的强度。尤其是在侧翻、袖孔、口袋上。沿缝进行强度试验,检查缝是否断裂 |
FAILED | |
Perform a carton drop test on the export cartons:10 times(1 corner 3 edges 6 faces)-3 cartons | FAILED | |
Fitting check on a model or a doll(每个款每个色拍照) 模特或模型试装 |
PASSED | |
Rub test to check the color fastness of the fabric (including the lining) and all the accessories(Labels must be rubbed for this test). Use a white cotton cloth to rub the material. Rub the item 10 times over a 10 cm distance with a force of 9N (1kg). Test 1 piece per color with both a dry and a wet cloth. Expected result: There should be no color transfer greater than 4 on a grey scale (between the original white cloth and the colored one) after the dry test. There should be no color transfer greater than 3-4 on a grey scale (between the original white cloth and the colored one) after the wet test 摩擦试验:检查织物(包括衬里)和所有附件的色牢度(此试验必须摩擦标签)。用一块白棉布擦这块材料。以9N (1kg)的力在10厘米的距离内摩擦物品10次。用干布和湿布各测试一种颜色。预期结果:干燥试验后,原白布与有色布之间的灰度转移不应大于4。湿布后,灰度(原白布与有色布之间)不得有大于3-4的颜色转移 |
FAILED | |
Zipper resistance test The zipper should be easy to closed and open (should pass resistance test) and should not block half way of the opening or closing -II 拉链阻力试验,拉链应该易于关闭和开放(应该通过阻力测试)和不应该妨碍一半的打开或关闭 |
FAILED | |
3M Adhesive test for all markings, printing and logos found-The printing, markings & logos easily peel off. For example: on surface of hardwares, heat transfer label, printing care label, etc.(3M胶带测试) | PASSED | |
Smell check-check if there are any strong offensive odor-II(鼻子闻下是否有气味) | PASSED |
3rd party preshipment products goods factory onsite inline final Random AQL PSI TPI FRI DUPRO third party on-site in-line pre-shipment QA QC check quality control assurance services in China India Vietnam Thailand Malaysia Bangladesh Taiwan.